ADC0808 PDF

The ADC IC is a commonly used ADC module for projects were an external ADC is required. Find ADC pin diagram, features & datasheet. ADC – A/D converters, used to convert analog signal to digital signals, like ADC IC, ADC IC, pin configurations and interfacing with microcontroller . The ADC/ADC is an 8 bit ADC that also contains an 8 channel multiplexer. The FPGA used in this case was the Altera 10k20RC that is found on.

Author: Zulkizragore Vuramar
Country: Sweden
Language: English (Spanish)
Genre: Career
Published (Last): 10 February 2014
Pages: 349
PDF File Size: 17.30 Mb
ePub File Size: 4.5 Mb
ISBN: 241-2-86427-839-3
Downloads: 68609
Price: Free* [*Free Regsitration Required]
Uploader: Gardagar

The OE signal should conform to the same range as all the other control signals. The clock should conform to the same range as all other control signals. It is a pulse of at least ns in width. In the above wdc0808 I have used a potentiometer to feed in a variable voltage of 0V to 5V to adf0808 IN1 pin and the present Voltage is read using a voltmeter.

The major advantage, of using ADC is that, we noise can be efficiently eliminated from the original signal and digital signal can travel more efficiently than analog one. Top menu About Us Contact.

Clock The clock signal is required to ad0c808 through the comparator stages to do the conversion. The source resistance must be below 10kohms for operation below kHz and below 5kohms for operation around 1.

This is an address select line for the multiplexer. Vref is connected to ground normally.

Related Posts  CADWELD ONE SHOT PDF

IC ADC0808

Analog Channel 1 to 5. And show on LCD as name Ch2. Choosing Motor For Robots. Signal from the ADC. Instead of continuous conversion, ADC converts data periodically, which is usually known as sampling rate.

That is because ADCs require clocking and can contain control logic including comparators and registers. If Vcc and ground are used as reference voltages, they should be isolated by decoupling with a 1 microF capacitor. The source code provided was used to control an ADC where only 4 inputs were used, therefore, ADD C is tied to ground and so are the unused inputs.

The default step size is Digital output bit 4. When we select microcontroller family for making any project, in which we need of an ADC conversion, then we use external ADC.

Analog to Digital Converter – ADC/ADC

That is for every increase of And like wise for other channels. The right input analog voltage can be given to adc008 from IN1 to IN7, but the IC can read the voltage of only one channel at a time. The signal goes low once a conversion is initiated by the start signal and remains low until a conversion is complete. Start conversion; input pin; a low adc8008 high pulse is given.

For selecting all the other input channels, have a look on the given table: Then microcontroller shows its value at Ch1 position in LCD. Log in or register to post Comment.

ADC Interfacing With | EmbeTronicX (Embedded Tutorials Zone)

Start The purpose of the start signal is two fold. It is the LSB of the select lines. These three pins are used to select the channel. Bottom rail of Reference voltage. The signal can be tie to the ALE signal when the clock frequency is below kHz.

Related Posts  COURS D ELECTROSTATIQUE PDF

This means that in order to get it to ad0808, there is a total of seven control signals that must be sent from the FPGA. This pin is should be temporarily made high to adc088 ADC channel.

Top rail of Reference voltage. A 9 volt battery and a 5 volt voltage regulator namely are used for powering the circuit. Latest Blogs Aadc0808 Browsers: It can be tied to the Start line if the clock is operated under kHz.

This is an output pin which goes high once the conversion is over.

ADC0808 IC

ADC is the Analog to Digital converterwhich converts analog data avc0808 digital format; usually it is used to convert analog voltage into digital format. ADC gives ratio metric conversion output at its output pins.

Skip to main content. The step size is decided based on set reference value. The other files are enabled register, a register, and a multiplexer. Has to be given clock signals 0V-5V 20Mhz approx.

Hope this helps CODE: