ArcWear performs vertical flame testing for textiles in accordance with ASTM D which is used in ASTM F, ASTM F, and NFPA We will report. 23 Jul Some updates have been made to ASTM D Standard Test Method for Flame Resistance of Textiles (Vertical Test) commonly used in flame. ASTM D Test Method for Flame Resistance of Textiles. (Vertical Test). • Pass criteria: max char length of 10 cm. • After-flame of not more than 2 seconds.
|Published (Last):||9 July 2017|
|PDF File Size:||17.29 Mb|
|ePub File Size:||14.70 Mb|
|Price:||Free* [*Free Regsitration Required]|
NFPA 2112 – ASTM D6413: Vertical flame test method
The occurrence of melting or dripping, if any, is also astm d6413. The between-laboratory precision of this test method has not been established.
Save my name, email, and astm d6413 in astm d6413 browser dd6413 the next time I comment. The ASTM D test method is utilized to evaluate the flame resistance of every production lot of fabric used in Tyndale-branded clothing.
This is the defining test method for compliance with OSHA Combining values from the two systems may result in non-conformance with the standard. Notify me of new posts by email. The cut edge of the fabric on the bottom asfm exposed to a controlled methane flame for 12 seconds as seen axtm astm d6413 image above, left.
The test results from the two laboratories should be compared using a statistical astm d6413 for unpaired data, at a probability level chosen prior to the testing series. Historical Version s – view previous versions of standard.
The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of astm d6413 other. After exposure to the flame, afterflame, afterglow and char length are measured: Refer to Section 14 for single-laboratory precision.
ASTM D – 99 Standard Test Method for Flame Resistance of Textiles (Vertical Test)
astm d6413 Link to Active This link will always route to the current Active version of the standard. ICS Number Code Your email address will not be published.
ASTM D v6413 used to determine flame resistance of fabrics used to protect against both electric arc and flash fire hazards. As a minimum, the astm d6413 samples used should be as homogeneous as possible, astm d6413 are drawn from the material from which the disparate test r6413 are obtained, and that are assigned randomly in equal numbers to each laboratory for testing. Char Length is the length in inches of fabric destroyed by the flame.
Work Item s – proposed revisions of this standard. Tyndale performs voluntary safety auditing on Tyndale garment fabrics.
If a bias is found, either its cause must be found and corrected, or future test results must be astm d6413 in consideration on the known bias. Other materials with established test values may be used for astm d6413 purpose. Leave a Reply Cancel reply Your email address will not be published.
ASTM D Vertical Flame Test for Flame Resistance of Textiles – Tyndale USA
It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior wstm astm d6413. July 10, at 9: The purpose of this test is to astm d6413 whether a fabric will continue to burn after the source of ignition is removed.
Afterflame is the number of aastm during which there is a visible astm d6413 remaining on the fabric. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.
Adopted from Federal Test Standard No.
Garments that meet these standards are used to comply with: Afterglow is the number of seconds during which there is a visible glow remaining on the fabric.
We are Astm d6413 to Protect workers, and understand that our dedication to testing is the only way to ensure that our garments astm d6413 as expected — every time!
Five tests are performed and the results are averaged and reported as the final test astm d6413. Notify me of follow-up comments by email.