SAE J Revised JUL SHOULDER REFERENCE POINT 6* 30′ NOTE: DIMENSIONS ARE MM FIGURE 1— H-POINT TEMPLATE Position the. 26 May BY ORDER OF THE EXECUTIVE DIRECTOROffice of the Federal RegisterWashington, Authority of the Code of Federal Regulations. Document Name: SAE J Devices for Use in Defining and Measuring Vehicle Seating Accommodations CFR Section(s): 49 CFR (b) Standards Body.

Author: Barr Kagagul
Country: Great Britain
Language: English (Spanish)
Genre: Business
Published (Last): 9 December 2009
Pages: 126
PDF File Size: 10.18 Mb
ePub File Size: 20.76 Mb
ISBN: 183-2-24388-632-6
Downloads: 74724
Price: Free* [*Free Regsitration Required]
Uploader: Mezizil

Sae j826 the general installation procedure except when rocking the H-Point machine as outlined in 5. The heel may not be placed on the toe swe. All definitions and dimensions used in sxe with this document are described in SAE J The muslin should be tucked in a sufficient amount to prevent sae j826 of the material. Front Seat— Alternately lift each foot off the floor the minimum necessary amount until no additional forward foot movement is obtained.

ETD – Technical Trading – SAE J H-POINT-MANIKIN – ATD Crash-Test-Dummies

All definitions and dimensions used in conjunction with this document are described in SAE J1 When the seatback has an angular adjustment separate from the seat xae, the normal driving or riding seatback angle is specified by the manufacturer L Much like the Torso Angle reflects the torso attitude imposed by the seat back ase the three-dimensional H-Point machine.

A thigh bar attached to the seat pan establishes the thigh length and serves as a base line for the hip angle sae j826. Full text of ” SAE J Then carefully return the back pan to the sae j826. Increasing the sae j826 angle up to 3 degrees by increasing the applied force up to a maximum of 66 N b. In vehicles with no tunnel, set the H-Point machine’s feet approximately mm 10 eae apart.

Due to the movement of the feet during the H-Point machine rocking sae j826, the feet are repositioned as follows: Figure B1 for distribution of weights. Sae j826 this quadrant in place. The beam from the j8826 should meet the photometric specifications listed in the table when it is aimed to center the maximum intensity on the photometer axis, except that sae j826 the maximum exceeds 25, cp, the 25, cp point directly above the maximum intensity should be aimed at the photometer axis.


The weights will each lay propped outwardly in the sae j826 corner sxe the seat pan against the thigh weights. Two spirit levels orient the device in space. A quadrant is fastened to the probe to measure the back angle.

Follow the general installation sae j826 through 5. Other second seat compartment dimensions are recorded directly h826 the H-Point machine as positioned in A. A graduated sliding probe is hinged from the H-Point to measure the headroom in the compartment.

Criminal sae j826 may apply for noncompliance.

Follow the installation procedure through 5. Mechanical Force Gauge This mechanical force gauge is directly mounted onto the manikin. This robust measuring instrument works bidirectionally to record both force sae j826 weight measurement and has a high definition 0,01 N incl. Sae j826 digitale indicator sae j826 all relevant information in accordance to EU standard requirements. This measure uses the H-Point machine with lower legs removed and the torso weights redistributed about the seat pan.

Upon completion of the rocking motion and repositioning the H-Point machine’s feet under the seat, move the front seat back to its normal riding position.

SAE J826: Defining and Measuring Vehicle Seating Accommodation

Constructed of reinforced plastic and metal, it consists of a separate back pan and seat pan, mechanically hinged at the hip or “H. Positive stops are provided in the thigh and lower leg segments for the 10th, sae j826, and 95th percentile of adult male dimensions Table 1.

A quadrant is fastened to the probe to measure sae j826 back angle. SAE invites your written comments and suggestions. Cushion Angle is measured using the H-Point machine with sae j826 lower legs removed and the torso weights redistributed about the seat pan.

This standard is designed to be used in the accom- modation method of interior compartment dimensioning which utilizes the manikin, rather than sae j826 free seat contours, to define seating space in a vehicle.

The T-bar lateral segment should be parallel to the ground and perpendicular to the Y plane of the vehicle unless sae j826 specified by sae j826 manufacturer. Resume the general installation procedure, 5. Care must be exercised through the remainder of the procedure to prevent the H-Point machine from sliding forward. Search the history of over billion web pages on the Internet.

Related Posts  NORMA DIN 66399 PDF

Reposition the H-Point machine j26 the seat by one of the following methods: Second Seat— Alternately move each foot forward by applying a forward load to the heel of the foot, sliding the feet forward until the feet or leg interfere with sae j826 rear of sae j826 front seatback.

Other seated positions are specified in 4.

The left foot is positioned sae j826 the floor or toe pan and located approximately the same distance to the left of the H-Point machine centerline as the right foot is to the right. The foot angle is to be restricted to a maximum of degrees. Allow the Aae machine to slide rearward sae j826 a forward horizontal sae j826 load on the T-bar is no longer required due to the seat pan contacting the seatback.

The loaded H-Point machine should not be left on the assembly longer than the time required to perform the test. Because of the fast data collection Hzthe force eae can be precisely recorded e.

Normally, the H-Point machine thigh attitude depends on the seating package arrangement because the machine’s foot location in the package sets the angle of sae j826 lower sae j826 and thigh. If prefocused bulbs are used, the limiting positions at which tests are made shall be 0.

Full text of “SAE J Devices for Use in Defining and Measuring Vehicle Seating Accommodations”

All test data collected is sae j826 on a large high resolution reversible sae j826 with selectable engineering units either for force SI-unit Newton or weight measurement. Use 25 degrees if not specified. Constructed of reinforced plastic and metal, these separate back and seat pans simulate the human torso and thigh and are mechanically hinged at the H-Point.

Alternately place two torso weights next to saw buttock weights.